Fluke 705 Loop Calibrator

Low cost calibration muscle
The Fluke 705 Loop Calibrator is a cost-effective, integrated solution for calibration, repair and maintenance of current loops. It features:
• mA sourcing, simulation and measurement
• 0.02 % accuracy and 0.001 mA resolution
• Simultaneous mA and % of span display
• Selectable step or ramp outputs
• 24 V Loop supply with mA measure
• 0 V dc to 28 V dc measurement to check Loop Voltage
• Removable battery door for quick battery replacement
• Compact case with protective holster
• Three-year warranty

For pricing information, or to receive an official price quotation for the Fluke 705 Loop Calibrator, please click on the "Request Quote" button below.

Fluke 707 Loop Calibrator

The fastest, one-handed tool for loop checks
The Fluke 707 Loop Calibrator is a high performance solution for calibration, repair and maintenance of current loops. The “Quick Click” knob makes it extremely fast and easy to use. It features:
• One handed user interface with “Quick Click” detented knob
• mA sourcing, simulation and measurement
• 0.015 % accuracy and 0.001 mA resolution
• Simultaneous mA and % of span display
• Selectable step or ramp outputs
• 24 V Loop supply with mA measure, including 250 Ω HART resistor
• 0 V dc to 28 V dc measurement to check Loop Voltage
• Removable battery door for quick battery replacement
• Compact case with protective holster
• Three year warranty

For pricing information, or to receive an official price quotation for the Fluke 707 Loop Calibrator, please click on the "Request Quote" button below.

Fluke 787 ProcessMeter DMM Loop Calibrator

The Fluke-787 ProcessMeter combines a DMM and a Loop Calibrator in one rugged, handheld tool - for about what you would expect to pay for a loop calibrator alone. The 787 starts with the Fluke-87 DMM you know and trust, then adds ability to measure, source, and simulate DC loop current with 0.05% accuracy and 1 micro-amp resolution. When you carry the ProcessMeter, you're ready for any loop troubleshooting or calibration task. And since it’s dust- and splash-resistant and EMI-shielded, the 787 can survive in your tool belt.

·  DMM and Loop Calibrator in one tool
·  Precision 1000V, 440 mA digital Multimeter Measure AC and DC volts, AC and DC current, resistance, continuity, and frequency 0.1% DC voltage accuracy 0.05% DC current accuracy, 1 uA resolution to 30 mA Simultaneous mA and % of scale readout True RMS AC voltage measurement to 1 kHz Frequency measurement to 20 kHz Min/Max/Average/Hold/Relative modes Diode Test and Continuity Beeper
·  DC current source / loop calibrator 20 mA current source / simulator Simultaneous mA and % of scale readout Manual Step (25%, Coarse, Fine) plus Auto Step and Auto Ramp
·  Clear LCD with backlight; 4,000 counts (30,000 counts for DC current)
·  Externally accessible battery for easy battery changes
·  V overload protection on V, ohms, frequency
·  V overload protection on mA, backed-up by 440 mA 1000V fuse
·  Designed to meet 1000 volt IEC 1010 Cat III standards Measurement

Additional technical information is available by downloading the .pdf data sheet below.

For pricing information, or to receive an official price quotation for the Fluke 787 ProcessMeter DMM Loop Calibrator, please click on the "Request Quote" button below.

Fluke 789 ProcessMeter DMM Loop Calibrator 

Key new features of the Fluke 789
• 24 V Loop power supply
• HART mode setting with loop power (adds 250 ohm resistor)
• 100 % larger dual display
• 1200 ohm drive capability on mA source
• Enhanced backlight with two brightness settings
• 0-100 % mA Span Check buttons to toggle between 4 and 20 mA
• Infrared I/O serial port compatible with FlukeView® Forms Software Version 2.1 (available Feb. 2003)
• Externally accessible fuses for easy replacement

Additional technical information is available by downloading the .pdf data sheet below.

For pricing information, or to receive an official price quotation for the Fluke 789 ProcessMeter DMM Loop Calibrator, please click on the "Request Quote" button below.