Rohde & Schwarz ESH3 EMI Test Receiver, 9 kHz to 30 MHz 

The Test Receiver ESH3 demodulates and measures AM double-sideband, single-sideband, PM and FM signals, as well as sinusoidal and impulsive interference, over the range 9 kHz to 30 MHz.

• Field-strength measurements in conjunction with test antennas
• Radio-interference (EMI) measurements to CISPR, VDE and FCC regulations
• Interference (EMI) measurements to MIL and VG regulations
• Radiomonitoring, remote frequency measurements
• Selective voltage measurements in laboratory and test department

Additional technical information is available by downloading the .pdf data sheet below.

For pricing information, or to receive an official price quotation for the Rohde & Schwarz ESH3 EMI Test Receiver 9 kHz to 30 MHz, please click on the "Request Quote" button below.

Rohde & Schwarz ESHS10 EMI Test Receiver

The R&S ESHS10 EMI Test Receiver is a double-conversion heterodyne receiver covering the frequency range from 9 kHz to 30 MHz.
They can be manually operated, featuring high frequency resolution and accurate level indication, both average and quasi-peak.

Key Facts
• Comply with CISPR 16-1, VDE 0876 and ANSI C63.2
• For measurements to European Standards 55011 to 55022, ETS, FCC, VCCI and VDE 0871 to 0879
• Level measurement range -36 to +137 dBμV
• Frequency resolution 10 Hz
• Wide dynamic range
• High measuring accuracy
• Five preselection filters
• Battery or AC supply
• Parallel detectors for average, peak and quasi-peak indication
• Macros for automatic test runs 

Additional technical information is available by downloading the .pdf data sheet below.

For pricing information, or to receive an official price quotation for the Rohde and Schwarz ESHS10 EMI Test Receiver, please click on the "Request Quote" button below.

Rohde and Schwarz FSQ40 Spectrum/Signal Analyzer, 20 Hz to 40 GHz

The Signal Analyzer R&S®FSQ combines two instruments in one. It offers signal analysis at a demodulation bandwidth of up to 120 MHz with the dynamic range of a high-end spectrum analyzer.

• Frequency range: 20 Hz to 3.6 GHz, 8 GHz, 26.5 GHz and 40 GHz
• Dynamic range of a high-end spectrum analyzer
 -TOI + 25 dBm, typ.
 -1 dB compression +13 dBm, typ.
 -84 dB ACLR/3GPP with noise correction
• 28 MHz demodulation bandwidth (optional 120 MHz)
• 16 Msample I and Q memory, extendable up to 705 Msample
• Application firmware for digital demodulation measurement
 -Bluetooth®
 -GSM/EDGE/EDGE Evolution (EGPRS2)
 -3 GPP WCDMA, HSDPA, TD-SCDMA
 -3GPP, LTE
 -CDMA2000®, 1xEV-DV, 1xEV-DO
 -WLAN 802.11a/b/g/j/n
 -WiMAX 802.16-2004, 802.16e-2005
 -General purpose vector signal analysis

Frequency Range
• FSQ8: 20 Hz to 40 GHz

RF Performance
• DANL with preamplifier < -152 dBm (10Hz)
• SSB phase noise typ. - 133 dBc (1Hz) at 10 kHz offset, CF 640 MHz
• Phase-noise typ. - 160 dBc/Hz @ 10 MHz offset, CF 640 MHz
• TOI typ. ±25 dBm
• 1-dB-compression point + 13 dBm
• 3GPP ACLR 77 dB, 84 dB with noise correction
• ACLR for 4-carrier scenario: 77 dB with noise correction

Accuracy
• 0.3 dB total level uncertainty up to 3.6 GHz
• <0.1 dB linearity error down to -70 dB IQ Downconverter
• IF digitizer 14 bit 81.6 MHz (20.4 MHz IF)
• IF digitizer 326.4 MHz (option FSQ-B72)
• IQ Bandwidth (RF) 28 MHz (up to 120 MHz mwith option FSQ-B72)
• SFDR > 80 dB
• IQ memory 16 Msamples each I and Q; output via GPIB or LAN
• Sample rate: cont. settable from 10 kHz to 81.6 MHz; e.g. 20 MHz for IEEE802.11a

Speed
• 2.5ms sweep time in frequency domain
• 1 μs sweep time in time domain
• up to 70 remote measurements/s via GPIB
• up to 80 manual measurements/s (screen update)
 
Additional technical information is available by downloading the .pdf data sheet below.

For pricing information, or to receive an official price quotation for the Rohde and Schwarz FSQ40 Spectrum/Signal Analyzer, 20 Hz to 40 GHz, please click on the "Request Quote" button below.

Rohde & Schwarz NRP Power Meter Specifications 

• Innovative multipath sensor technology
• 90 dB dynamic range
• High measurement speed
• Intelligent sensors – simply plug in and measure
• Accurate measurement of average power regardless of bandwidth and modulation
• Multislot measurements for common time division systems (e.g. GSM/EDGE, DECT)
• Handling of external components through Γ and s-parameter correction
• Simultaneous operation of up to 4 sensors on basic unit
• Operation of sensor directly from PC USB interface
• 2-year calibration cycle

 Designed for R&D 

Top measurement accuracy plus a dynamic range of 90 dB for broadband signals of any modulation are the most requested characteristic s of a modern power meter. The versatile R&S NRP sensors in feature exactly these characteristics and are a priceless investment if you wish to meet future requirements such as the broadband modulation types of thirdgeneration mobile radio. In addition, they are also capable of handling the RF bandwidths beyond 100 MHz that are already under discussion for wireless LAN.

A power meter must of course be easy to operate: The numerous sensor functions can be activated via an intuitive user interface, and the high-resolution display indicates up to 4 measurement results at a time. As with other power meters from Rohde & Schwarz, all calibration data is stored in the sensor, which ensures highprecision measurements by minimizing operating errors. 

Ideal for production

If you have ever dealt with microwave power measurements, you know that the necessary filtering of results due to the noise characteristics of the sensor as well as delays in measurement range selection and command/result processing can have negative effects on throughput in production. And this is where the R&S NRP with its innovative features offers straightforward solutions:

• Autofilter
• Parallel processing
• Speed

It goes without saying that the basic unit, which can accommodate up to 4 sensors at the same time, can be fully remotecontrolled. In addition, the sensors can directly be connected to a PC. It is good to know that the sensors can perform reliable measurements for an extended period of time owing to the long calibration interval of 2 years.

For pricing information, or to receive an official price quotation for the Rohde & Schwarz NRP Power Meter, please click on the "Request Quote" button below.

Rohde & Schwarz SME03 RF Signal Generator, 5 kHz to 3 GHz   
        
The SME supplies the complex signals required for the development and testing of digital mobile radio receivers. It is capable of generating all signals used in the main digital radio networks in line with relevant standards regarding the type of modulation, data format, TDMA structure and frequency hop patterns. The SME is completely at home also in the analog signal world of conventional signal generators.

Features:
• User-programmable data sequences and TDMA structure
• RF, LF and level sweep
• Ultra-low RF leakage for measurements on highly sensitive pagers
• List mode: programmable measurement sequence for up to 4096 frequency and level combinations, setting time <0.5 ms (not SME03E)

For pricing information, or to receive an official price quotation for the Rohde & Schwarz SME03 RF Signal Generator, 5 Khz to 3 GHz please click on the "Request Quote" button.

Rohde and Schwarz CMD52 Digital Radiocommunication Tester  

Features:
• All signalling required for GSM900 testing
• Highest measurement accuracy and speed
• Remote control via IEEE488/IEC625 bus
• Autotest and remote control via RS-232-C
• Go/nogo test as well as service mode for exact fault location

Additional technical information is available by downloading the .pdf data sheet below.

For pricing information, or to receive an official price quotation for the Rohde and Schwarz CMD52 Digital Radiocommunication Tester, please click on the "Request Quote" button below.

Rohde and Schwarz CMD55 Digital Radiocommunication Tester     

Features
• Mobile Phone Tester for all GSM bands (GSM900/1800/1900)
• Cost-effective solution for production lines
• Extremely fast IEEE-bus operation for high production throughput
• Versatile measurements for R&D and TQM
• High flexibility due to a various choice of parameter settings
• Full dynamic power ramp measurements according to GSM Recs
• Very fast spectrum due to modulation measurements with 5-pole filter prepared for measurements of DECT Fixed and Portable Parts (ETSI Rec. CTR06)

Additional technical information is available by downloading the .pdf data sheet below.

For pricing information, or to receive an official price quotation for the Rohde and Schwarz CMD55 Digital Radiocommunication Tester, please click on the "Request Quote" button below.

Rohde and Schwarz CMD60 Digital Radiocommunications Tester

Features:
• Compact, lightweight and extremely fast
• Suitable for service, production and development
• Remote control via IEEE488/IEC625 bus + RS-232-C
• Automated regression and stress testing of DUT
• Automatic go/nogo testing of fixed and portable part

Additional technical information is available by downloading the .pdf data sheet below.

For pricing information, or to receive an official price quotation for the Rohde and Schwarz CMD60 Digital Radiocommunications Tester, please click on the "Request Quote" button below.

Rohde and Schwarz CMU200 Universal Radio Communication Tester   

The CMU200 reflects the long-standing expertise Rohde&Schwarz has gained in the world of mobile radio. In recent years, the company has helped to launch overwhelmingly successful mobile radio systems.

Rohde&Schwarz is a preferred supplier to many of the leading mobile equipment manufacturers and is the market leader for mobile radio test sets.

The CMU200 is part of a complete range of mobile radio test equipment, encompassing everything from conformance test systems to system simulators, turnkey functional board test / final test systems and simple sales-counter Go/NoGo testers.

The base unit with its standard-independent module test provides many generalpurpose measurement facilities for the development of all kinds of standards within its wide and continuous frequency range. If extended by the relevant options, the CMU200 offers the hardware and software necessary to handle your 3G, 2.5G and previous-generation testing applications, including analog.

Key advantages of the CMU200
Speed
• Unrivalled speed of single measurements
Accuracy
• Incomparable accuracy
• Excellent result repeatability
Modularity
• Modular hardware and software concept provides easy extension to further functionality
Reliability
• Extremely low power consumption and effective heat conduction result in unparalleled reliability
Future-proof
• Easy migration to emerging standards

Additional technical information is available by downloading the .pdf data sheet below.

For pricing information, or to receive an official price quotation for the Rohde and Schwarz CMU200 Universal Radio Communication Tester, please click on the "Request Quote" button below.

Rohde and Schwarz CMU300 Universal Radio Communication Tester   

The CMU300 reflects the long-standing expertise Rohde & Schwarz has gained in the world of mobile communication and base station testing in different fields such as production, R&D, commissioning, system test, service and maintenance.

The CMU300 is designed to provide a flexible platform for customized solutions and testing with maximum speed, top accuracy and optimum repeatability. Its home is the world of digital mobile networks of generations 2 and 2.5. As a today‘s investment in the future it is prepared already for 3rd generation testing.

Key advantages of the CMU300
Speed
• Single measurement up to 10 times faster than with the previous generation of instruments
Accuracy
• Three times more accurate than the previous generation of instruments with excellent repeatability
Modularity
• Modular hardware and software concept provides easy extension to enhanced functionality
Bullet-Proof
• Low component count, low power consumption, and effective heat conduction result in unparalleled reliability
Future-proof
• Easy migration to future standards

Additional technical information is available by downloading the .pdf data sheet below.

For pricing information, or to receive an official price quotation for the Rohde and Schwarz CMU300 Universal Radio Communication Tester, please click on the "Request Quote" button below.